Author Topic: How do I add new enemy to the existing group?  (Read 7778 times)

Kudistos Megistos

  • Banned
  • No life
  • *
  • Posts: 3936
  • Karma: 1
    • View Profile
Re: How do I add new enemy to the existing group?
« Reply #25 on: 2009-08-14 19:21:00 »
Actually, initial status would have to have been 4 bytes like the status immunities, because one byte alone cannot point to all the possible status conditions that can be active on the enemy, otherwise the status immunity section would have only been one byte, but that is only possible with 8 statuses, and there are definitely more than 8 :P.

I was thinking that it might work like the status defence and status attack parts of weapon and armour data that are one byte and can only identify one status. I'll have a look at this.

it is likely that the 2 byte unknown was originally a fourth manip/berserk move that was scrapped for whatever reason at the end.

That seems quite sensible. Have you tried putting anything in there to see whether an enemy can actually have a fourth attack? I don't think it would work, but...

as for the 32 byte unknown, that would require looking at every enemy's data to see if there is a possible pattern to be seen, it is hard to tell from a few enemies :P. here are a few more enemies and their values (including the ones you mentioned KM) maybe throwing a few out there will get some ideas flowing, though it would still be easier with a complete list of all enemies and their values:

Grunt - d200 (3rd/4th bytes)
Sweeper - 5e01 (5th/6th bytes)
Guard Scorpion - 1301 (11th/12th and 13th/14th bytes)
Grashtrike - 1301 (3rd/4th bytes)
Rocket launcher - d600 (first two bytes)
Blugu - d700 (3rd/4th bytes)
Special Combatant - d200 (3rd/4th bytes)
Smogger - d800 (5th/6th bytes)
Air Buster - db00 (5th/6th and 7th/8th bytes), 1301 (15th/16th bytes)

i think all of these share the same position as a specific attack the enemy uses (as in the same position as the 32 block of the enemy's attacks), so it could be something to do with the camera movement, guard scorpion has 1301 set in the same position as the two unnamed moves it uses to switch between stages, and grashtrike has it in the same position as it's silk attack. the way to figure out what it is would be to compare the way the moves are used with the value there, and with the value as FFFF (i.e. unused), but my guess is that is somehow changes the camera, possibly by "borrowing" the animation used by another attack. it is probably likely that my guess about what it does is wrong (since they would likely just replace the camera movement in the attack data instead of borrowing the camera from another), but it definitely has to be related to the moves in some way.

Something else for me to try :-P

Of course, it might be that some or all of these things used to what the things we think they might be doing but have been dummied out, in which case we might be looking for a long time :roll:

secondadvent

  • Insane poster
  • *
  • Posts: 287
  • Karma: 0
    • View Profile
Re: How do I add new enemy to the existing group?
« Reply #26 on: 2009-08-14 19:25:15 »
yeah, it is possible that they are all dummied out, having to rewrite the entire pointing crap/removing the now unneeded data is much more work than just making it all useless :P.

i think i may have tried to add an extra move to the data after the manip attacks at one point in time, but do not remember the results, so it was likely that it did nothing  :roll:. no harm in testing it again though  :lol:.

oh, and i may not be right on this (nfitc1 is the "master of the kernels", so he would know for sure XD), but i think that the weapon status infliction is only one byte because only one status can be inflicted by one weapon, so they would only need to make it one byte, whatever the value is would be the status it can inflict (so 27/26 (depending if it starts from one or zero) would be the darkness status). for the initial statuses/immunities, it is possible to have all active at the same time (though not likely to happen, it is possible), so to do it the same as the weapon would take 32 bytes, one to show each active status, so the better way in that situation would be four bytes, each bit being a flag for a status, four bytes on a weapon that is only allowed one status to inflict is similar, more bytes than needed, though if it could activate more than one status it would be better with four. i hope you see what i mean, i am not the best at explaining things, and i may not even be right on the way the weapon status byte is... i am just assuming i am right :P.

yeah, i just checked again and adding another move to the spot after the three manip moves does nothing to the manip screen, so it is likely dummied out. and the second "status" section also did nothing, as you said... just making sure :P.
« Last Edit: 2009-08-14 19:54:19 by secondadvent »