GF4 Ti 4200 + FF7 FSAA

[ye-roon]

I got a GF4 ti 4200. thus i tried the code change n stuff:

this piece of code

Code: [Select]

Required05 = 200h,

is replaced by this

Code: [Select]

FSAAMode06=ff06
FSAAMode0C=ff0c
FSAAMode0D=ff0d

using that method. SO doesn't this mean that there isn't a REquired05 ne more, or in other words, there is nothing for 2 x 2 mode to draw its requirements from. The code replacing also doesn't work for me in this format. i still have the sameweird lines and ugly backgrounds, so far i tried 45.23 and 52.13 drivers, will try 53.03 now and after that 56.xx

screens from 56.64
this is with the changed code
http://stud.hro.nl/0549792/2x2metback.jpg
http://stud.hro.nl/0549792/2x2metbtl.jpg

this is with original code
http://stud.hro.nl/0549792/2x2zonderback.jpg
http://stud.hro.nl/0549792/2x2zonderbtle.jpg

If you use nv17 (or above), fsaamode05/06/0C/0D should be ok with FF7pc.

what is nv17??

and i tried all those fsaamodes and they all seem to worsen the farther the number goes

oh i found something out..

i don't know what all the technical stuff means suff but:
when i put aa to 2 x 1 the horizontal lines are gone, but the vertical lines are not. when i use  1 x 2 the vertical lines are gone horizontal lines are not. also i uninstalled the 52.16 before installing the 53.03 drivers and RT still says some versions of the drivers are 52.16 well ne way all these AA modules don't work for me afaik (

oh and if someone has RT 14.1 installer or a link to it

[Srethron Askvelhtnod]

what is nv17??

Now there's a question I haven't seen in about two years.
The short answer is this:
nv17 == all nVidia chips in the GeForce 4 MX series
nv25 == all nVidia chips in the GeForce 4 TI series

So you have an nv25. Which is a good thing, since nv17 cards aren't as good as nv25 (no nfiniteFX-engine, no directX 8 support, etc.)

Based on this info, when you hear people talking about nv30, I trust you'll be able to figure out what cards they're referring to.

[halohalo]

I got a GF4 ti 4200. thus i tried the code change n stuff:

this piece of code

Code: [Select]

Required05 = 200h,

is replaced by this

Code: [Select]

FSAAMode06=ff06
FSAAMode0C=ff0c
FSAAMode0D=ff0d

using that method. SO doesn't this mean that there isn't a REquired05 ne more, or in other words, there is nothing for 2 x 2 mode to draw its requirements from. The code replacing also doesn't work for me in this format. i still have the sameweird lines and ugly backgrounds, so far i tried 45.23 and 52.13 drivers, will try 53.03 now and after that 56.xx

screens from 56.64
this is with the changed code
http://stud.hro.nl/0549792/2x2metback.jpg
http://stud.hro.nl/0549792/2x2metbtl.jpg

this is with original code
http://stud.hro.nl/0549792/2x2zonderback.jpg
http://stud.hro.nl/0549792/2x2zonderbtle.jpg

You need to enable 8bit paletted textures with RivaTuner.